6-6-8-zamena-ehlementov-privoda-stoyanochnogo-tormoza.html
6.6.8. Replacement of elements of the drive of the parking brakeBy preparation for replacement of elements it is necessary to switch off ignition, to remove a ware tray, the rubber panel, to turn out three screws and to remove a back part of the console.
Works on replacement of elements of the drive should be performed in such order:
1) removal of the handle of the parking brake:
|
Fig. 6.17. Fastening of the handle of the parking brake: 1 — the cable balance weight; 2 and 4 — bolts;
3 — the switch socket
|
— remove the socket 3 switches of the parking brake (fig. 6.17);
— turn out bolts 2 and 4 fastenings of an arm of the handle of the parking brake;
— remove the central cable from the balance weight 1;
— remove the handle of the parking brake;
2) replacement of the central cable of the parking brake:
— turn off an adjusting nut and remove a lock bracket;
— unbend a uvula from below;
— take out the central cable;
— establish a new central cable so that the top part of a cable settled down vertically at the installed handle;
— bend a uvula back, put a lock bracket and a nut;
3) replacement of the plug of the handle of the parking brake:
— clamp the handle in a vice;
— smoothly involve the plug from the handle. If necessary heat the plug a fan heater;
4) installation of the handle of the parking brake:
— fix the central cable of the parking brake on the balance weight 1 (see fig. 6.17);
— put the handle of the parking brake and tighten bolts 2 and 4. Moment of an inhaling of 25 N · m;
— connect the socket 3;
5) replacement of the switch of the parking brake:
— delay the handle of the parking brake that it did not close the switch;
— turn out the screw and remove the switch;
— put the new switch;
— tighten the screw the moment of 27 N · m;
— check work of a brake;
6) a detachment of a cable of the parking brake in the car:
|
Fig. 6.18. Connection of cables with the brake handle: 1 — the handle; 2 — the balance weight; 3 — a cable
|
— install the handle 1 (fig. 6.18) of the parking brake in the lower situation and wring out a cable of the parking brake;
— remove the end of a cable from the balance weight 2. For removal of the right cable at first remove the left cable;
|
Fig. 6.19. Fastening of a cable under the car
|
— remove a back seat;
— delay a molding of a back threshold and lift a floor covering;
— remove a clamp of the holder of a cable and pass a cable through an eye back;
7) removal of a cable of the parking brake under the car:
— remove a mudguard (at removal of the left cable).
— remove a cable from a body and suspension brackets;
— remove a cable from the holder on a support of a brake and disconnect an internal cable from the lever;
— give a cable forward and remove it together with the plug from the car;
8) installation of a cable of the parking brake under the car:
— pass a cable of the parking brake through an opening in a floor and put the plug;
— connect a cable of the parking brake to a support;
— fix a cable in a forward part of a body by means of the holder;
— connect an internal cable to the lever of a support and pass an external cable in the holder;
— fix a cable of the parking brake in holders;
— put a mudguard (when replacing the left cable);
9) installation of a cable of the parking brake in the car:
— pass a cable of the parking brake through an arm and under a floor covering forward;
— pass an internal cable through an eye and pass an external cable in the holder of the handle of the parking brake;
— fix an internal cable (cables) on the holder;
— put into place the back holder. Tighten the moment 25 N · m;
— check position of the plug;
— lay a floor covering and put a threshold molding;
— put into place a back seat. Tighten fastening details the moment of 25 N · m;
10) adjustment of the parking brake (see in subsection. "Replacement of brake shoes of back wheels").
|