S40/V40
1. General information
2. Operation and maintenance of the car
3. Design and technical characteristics of engines
4. Repair of the engine
5. Transmission
6. Brake system
7. Forward suspension bracket and steering
8. Back suspension bracket
9. Control system of the Fenix 5.1 engine
10. Electric equipment. Conducting and components
11. Body
11.1. General information
11.2. Control sizes of a body
11.3. Ways of connection of details at restoration of operational qualities of a body
11.4. Repair of a body
11.5. Removal and installation of elements of a body of the car
11.5.1. Removal and installation of a cowl
11.5.2. Removal and installation of a forward wing
11.5.3. Adjustment of situation and clamp of the lock of doors
11.5.4. Removal of panels of facing of doors
11.5.5. Removal and installation of a door assembled
11.5.6. Removal and installation of the lock of a forward door
11.5.7. Removal and installation of the lock of a back door
11.5.8. Replacement of the mechanism of a window regulator of a forward door
11.5.9. Replacement of the mechanism of a window regulator of a back door
11.5.10. Installation of mechanisms of window regulators
11.5.11. Replacement of a gas-filled emphasis of a trunk lid
11.5.12. Adjustment of provision of a trunk lid
11.5.13. Replacement of elements of the lock of a trunk lid
11.5.14. Replacement of the mechanism of the lock of a trunk lid
11.5.15. Adjustment of the lock of a trunk lid
11.5.16. Replacement of a door of a back
11.5.17. Replacement of the lock of a door of a back
11.5.18. Removal and installation of the mechanism of the lock of a door of a back
11.5.19. Replacement of the block of a back lamp assembled
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
11.5.21. Removal and installation of bumpers
11.5.22. Replacement of a front seat assembled
11.5.23. Replacement of the locking mechanism of a back of a back seat
11.5.24. Replacement of internal facing of a roof
11.5.25. Replacement of a floor covering
11.5.26. Removal of the back central console
11.5.27. Removal of the forward central console
11.5.28. Removal of the dashboard assembled
11.5.29. Replacement of the dashboard
11.5.30. Installation and adjustment of a cable of control of the air mixer
11.5.31. Installation of a combination of devices
12. Schemes of electric equipment
 



13c91ae0




11-5-7-snyatie-i-ustanovka-zamka-zadnejj-dveri.html

11.5.7. Removal and installation of the lock of a back door

At removal of the lock of a back door act as follows:
— remove the panel of facing of a back door;

Fig. 11.65. Points of fastening of an arm (are shown by shooters)


— having unscrewed 2 screws self-tapping screws, remove an arm (fig. 11.65);
— accurately remove a noise isolation;

Fig. 11.66. The elements dismantled at removal of the lock of a back door: 1 — screws of fastening of an overlay of a back door, 2 pieces (torx 30);
2 — the screw (torx 25)


— turn out two screws 1 (fig. 11.66);
— turn a slip forward and at the same time remove it the movement up;
— extend a sealant from a guide;
— turn out the screw 2 of a slip;
— delay a windowpane guide for a sealant and remove;

Fig. 11.67. The elements dismantled at removal of the handle of the lock of a back door: 1 — bolts of fastening of the handle of a back door, 2 pieces; 2 — latches of fastening of the handle; 3 — draft of the lock of a door


— turn out two bolts of 1 (fig. 11.67) and remove a slip;
— press latches 2 from below;
— press draft 3 inside in the direction of an arrow and remove from a clip;
— take out the door handle the movement up;
— open a fixing bracket, turn up and remove the blocking draft from the lock;

Fig. 11.68. Removal of the lock of a back door:
1 — screws self-tapping screws of fastening of the handle of a back door; 2 — draft; 3 — screws of fastening of the lock of a back door (3 pieces)


— turn out screws self-tapping screws 1 and remove draft 2 from a clamp in the direction of an arrow (fig. 11.68);
— turn out screws 3 with a face head;
— press the lock and remove the unlocking draft;
— turn the lock outside, separate sockets and remove the lock.
Installation of the lock of a back door is made upside-down, taking into account the following remarks:
1) adjust the unlocking handle for what:
— close, and then open the lock;
— remove the block from a clamp and adjust draft;
— press both drafts in a guide;
— wrap screws 3 with a face head (the moment of an inhaling of 6 N · l);
2) install the door handle (fig. 11.67) for what:
— check consolidation;
— press the holder on the place, put a slip and adjust the provision of consolidation;
— having delayed draft 3 down, insert it into a clip of the internal lock;
— wrap bolts of 1 fastening of the door handle (the moment of an inhaling of 10 N · l);
— check functioning and put a sealant;
3) establish a windowpane guide for what:
— grease a sealant and a guide;
— tighten glass guide bolts (the moment of an inhaling of 10 N · l);
— you make further installation of a guide as it should be, the return to removal;
4) install the panel of facing of a door for what:
— mount a noise isolation on a door;
— make the necessary openings in the new panel;
— grease a contact profile with soap solution;
— you make further installation of the panel of a door as it should be, the return to removal.

"previous page
11.5.6. Removal and installation of the lock of a forward door
following page"
11.5.8. Replacement of the mechanism of a window regulator of a forward door