S40/V40
1. General information
2. Operation and maintenance of the car
3. Design and technical characteristics of engines
4. Repair of the engine
5. Transmission
6. Brake system
7. Forward suspension bracket and steering
8. Back suspension bracket
9. Control system of the Fenix 5.1 engine
10. Electric equipment. Conducting and components
11. Body
11.1. General information
11.2. Control sizes of a body
11.3. Ways of connection of details at restoration of operational qualities of a body
11.4. Repair of a body
11.5. Removal and installation of elements of a body of the car
11.5.1. Removal and installation of a cowl
11.5.2. Removal and installation of a forward wing
11.5.3. Adjustment of situation and clamp of the lock of doors
11.5.4. Removal of panels of facing of doors
11.5.5. Removal and installation of a door assembled
11.5.6. Removal and installation of the lock of a forward door
11.5.7. Removal and installation of the lock of a back door
11.5.8. Replacement of the mechanism of a window regulator of a forward door
11.5.9. Replacement of the mechanism of a window regulator of a back door
11.5.10. Installation of mechanisms of window regulators
11.5.11. Replacement of a gas-filled emphasis of a trunk lid
11.5.12. Adjustment of provision of a trunk lid
11.5.13. Replacement of elements of the lock of a trunk lid
11.5.14. Replacement of the mechanism of the lock of a trunk lid
11.5.15. Adjustment of the lock of a trunk lid
11.5.16. Replacement of a door of a back
11.5.17. Replacement of the lock of a door of a back
11.5.18. Removal and installation of the mechanism of the lock of a door of a back
11.5.19. Replacement of the block of a back lamp assembled
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
11.5.21. Removal and installation of bumpers
11.5.22. Replacement of a front seat assembled
11.5.23. Replacement of the locking mechanism of a back of a back seat
11.5.24. Replacement of internal facing of a roof
11.5.25. Replacement of a floor covering
11.5.26. Removal of the back central console
11.5.27. Removal of the forward central console
11.5.28. Removal of the dashboard assembled
11.5.29. Replacement of the dashboard
11.5.30. Installation and adjustment of a cable of control of the air mixer
11.5.31. Installation of a combination of devices
12. Schemes of electric equipment
 



13c91ae0




11-5-6-snyatie-i-ustanovka-zamka-perednejj-dveri.html

11.5.6. Removal and installation of the lock of a forward door

Fig. 11.60. An arrangement of the elements dismantled at removal of the lock of a door: 1 — a clamp; 2 — the holder; 3 — percussion caps (4 pieces); 4 — a SIPS system element


At removal of the lock of a forward door (fig. 11.60) act as follows:
1) remove the panel of facing of a forward door;
2) remove a door noise isolation for what:
— remove the holder 2, a percussion cap 3 and a clamp 1;
— accurately remove the loudspeaker of the audio system and a noise isolation (partially);
— remove an element of the SIPS 4 system together with the holder (2 screws);

Fig. 11.61. An arrangement of the elements dismantled at removal of a guide of windowpanes: 1 — a bolt of fastening of a guide


3) remove a guide of a windowpane (fig. 11.61) for what:
— extend a rubber sealant from a guide;
— turn off a bolt 1;
— delay a guide down and remove;

Fig. 11.62. An arrangement of the elements dismantled at removal of the internal lock of a forward door: 1 — the screw self-tapping screw of fastening of the handle of unlocking of a door; 2 — a latch; 3 — screws of fastening of the lock (3 pieces); 4 — the lock of a forward door;
5 — the blocking rod


4) remove knot of the internal lock of a forward door (fig. 11.62) for what:
— unscrew the screw self-tapping screw 1;
— disconnect the handle of unlocking of a door;
— shift a guide forward and extract glass (wring out a latch 2 from within);
— take out drafts from clips from the unlocking handle;
— to a vypressuyta a conducting plait clamp from the lower part of a door;
— turn out face screws 3 and press the lock 4;
— remove the blocking rod 5 from the internal lock;
— take draft from the lock and remove lock knot;

Fig. 11.63. Location of elements of fastening of the door handle: 1 — bolts of fastening of the door handle, 2 pieces.


5) remove the door handle (fig. 11.63) for what:
— turn out two bolts 1 and remove a slip;
— press latches from below;
— press draft inside and remove from a clip;
— take out the door handle the movement up;

Fig. 11.64. Removal of the cylinder of the lock: 1 — the screw of fastening of the mechanism of the lock of a door; 2 — a sealing ring; 3 — the lever; 4 — a spring


6) remove the mechanism of the lock (fig. 11.64) for what:
— insert a key into the lock;
— turn out the screw 1, remove a ring 2 and the lever 3;
— accurately remove a spring 4 that it did not jump out;
— remove the lock with a key.
You make installation of the mechanism of the lock as follows:
— grease the mechanism;
— put a sealing ring;
— establish a key code (if necessary);
— insert a key into the lock and install the mechanism of the door lock;
— put a spring with a cover;
— adjust the provision of a latch and wrap the screw.
You make further assembly of a door as it should be, the return to dismantling.


"previous page
11.5.5. Removal and installation of a door assembled
following page"
11.5.7. Removal and installation of the lock of a back door