S40/V40
1. General information
2. Operation and maintenance of the car
3. Design and technical characteristics of engines
4. Repair of the engine
5. Transmission
6. Brake system
7. Forward suspension bracket and steering
8. Back suspension bracket
9. Control system of the Fenix 5.1 engine
10. Electric equipment. Conducting and components
11. Body
11.1. General information
11.2. Control sizes of a body
11.3. Ways of connection of details at restoration of operational qualities of a body
11.4. Repair of a body
11.5. Removal and installation of elements of a body of the car
11.5.1. Removal and installation of a cowl
11.5.2. Removal and installation of a forward wing
11.5.3. Adjustment of situation and clamp of the lock of doors
11.5.4. Removal of panels of facing of doors
11.5.5. Removal and installation of a door assembled
11.5.6. Removal and installation of the lock of a forward door
11.5.7. Removal and installation of the lock of a back door
11.5.8. Replacement of the mechanism of a window regulator of a forward door
11.5.9. Replacement of the mechanism of a window regulator of a back door
11.5.10. Installation of mechanisms of window regulators
11.5.11. Replacement of a gas-filled emphasis of a trunk lid
11.5.12. Adjustment of provision of a trunk lid
11.5.13. Replacement of elements of the lock of a trunk lid
11.5.14. Replacement of the mechanism of the lock of a trunk lid
11.5.15. Adjustment of the lock of a trunk lid
11.5.16. Replacement of a door of a back
11.5.17. Replacement of the lock of a door of a back
11.5.18. Removal and installation of the mechanism of the lock of a door of a back
11.5.19. Replacement of the block of a back lamp assembled
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
11.5.21. Removal and installation of bumpers
11.5.22. Replacement of a front seat assembled
11.5.23. Replacement of the locking mechanism of a back of a back seat
11.5.24. Replacement of internal facing of a roof
11.5.25. Replacement of a floor covering
11.5.26. Removal of the back central console
11.5.27. Removal of the forward central console
11.5.28. Removal of the dashboard assembled
11.5.29. Replacement of the dashboard
11.5.30. Installation and adjustment of a cable of control of the air mixer
11.5.31. Installation of a combination of devices
12. Schemes of electric equipment
 



13c91ae0




11-5-5-snyatie-i-ustanovka-dveri-v-sbore.html

11.5.5. Removal and installation of a door assembled

Fig. 11.59. Removal of a door assembled


You make removal of a door in collecting (fig. 11.59) as follows:
— mark location of a loop;
— take out an adjusting pin (in need of it it is possible to press out);
— uncover a conducting plait a rack And or In;
— disconnect the socket outside, press a white latch in front (a forward door), or uncover a conducting plait (a back door);
— disconnect sockets (press a latch);
— turn out bolts from lateral face of a door.
Assembled you make installation of a door as follows:
— establish a door on tags and tighten bolts half;
— put an adjusting pin of the limiter of opening of a door;

       NOTE
Put an adjusting pin so that its cut was directed along the limiter of opening of a door.

— connect the socket and put a conducting plait cover in a rack In;
— adjust the provision of a door (see соотв. section);
— tighten bolts of loops of a door (the moment of an inhaling of 21 N · м).

       NOTE
For new doors at first remove a ring from a loop.

"previous page
11.5.4. Removal of panels of facing of doors
following page"
11.5.6. Removal and installation of the lock of a forward door