S40/V40
1. General information
2. Operation and maintenance of the car
3. Design and technical characteristics of engines
4. Repair of the engine
5. Transmission
6. Brake system
7. Forward suspension bracket and steering
8. Back suspension bracket
9. Control system of the Fenix 5.1 engine
10. Electric equipment. Conducting and components
11. Body
11.1. General information
11.2. Control sizes of a body
11.3. Ways of connection of details at restoration of operational qualities of a body
11.4. Repair of a body
11.5. Removal and installation of elements of a body of the car
11.5.1. Removal and installation of a cowl
11.5.2. Removal and installation of a forward wing
11.5.3. Adjustment of situation and clamp of the lock of doors
11.5.4. Removal of panels of facing of doors
11.5.5. Removal and installation of a door assembled
11.5.6. Removal and installation of the lock of a forward door
11.5.7. Removal and installation of the lock of a back door
11.5.8. Replacement of the mechanism of a window regulator of a forward door
11.5.9. Replacement of the mechanism of a window regulator of a back door
11.5.10. Installation of mechanisms of window regulators
11.5.11. Replacement of a gas-filled emphasis of a trunk lid
11.5.12. Adjustment of provision of a trunk lid
11.5.13. Replacement of elements of the lock of a trunk lid
11.5.14. Replacement of the mechanism of the lock of a trunk lid
11.5.15. Adjustment of the lock of a trunk lid
11.5.16. Replacement of a door of a back
11.5.17. Replacement of the lock of a door of a back
11.5.18. Removal and installation of the mechanism of the lock of a door of a back
11.5.19. Replacement of the block of a back lamp assembled
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
11.5.21. Removal and installation of bumpers
11.5.22. Replacement of a front seat assembled
11.5.23. Replacement of the locking mechanism of a back of a back seat
11.5.24. Replacement of internal facing of a roof
11.5.25. Replacement of a floor covering
11.5.26. Removal of the back central console
11.5.27. Removal of the forward central console
11.5.28. Removal of the dashboard assembled
11.5.29. Replacement of the dashboard
11.5.30. Installation and adjustment of a cable of control of the air mixer
11.5.31. Installation of a combination of devices
12. Schemes of electric equipment
 



13c91ae0




11-5-24-zamena-vnutrennejj-oblicovki-kryshi.html

11.5.24. Replacement of internal facing of a roof

       NOTE
Completely open the moving hatch in a roof if it is available. Disconnect a negative wire from the rechargeable battery.

You make replacement of internal facing of a roof as follows:

Fig. 11.90. Fastening of the panel of facing are resistant And


1) remove the panel of facing of a rack And (fig. 11.90) for what delay the panel from a frame of a window and remove up;

       NOTE
If the mirror with illumination is installed in the car, it is necessary to disconnect the socket on a rack And.


Fig. 11.91. Points of fastening of a plafond of lighting


2) remove a forward plafond of illumination of salon (fig. 11.91) for what:
— uncover at the left and on the right;
— turn out two screws and remove a plafond of illumination of salon from a roof;
— disconnect the socket rotary motion;

Fig. 11.92. Fastening of ultrasonic sensors


3) remove ultrasonic sensors of the security alarm system (fig. 11.92) for what:
— to a vypressuyta sensors from an arm;
— remove an arm from internal facing of a roof, having pressed it into assembly grooves;
— remove sun-protection peaks and their arms;
— remove the hand-rail fixed on a ceiling;
— remove panels of facing of a rack In;
— remove back lamps for reading;
— remove back lighting plafonds in 5-door option;
— remove rack panels With;
— remove panels of a rack of D;
— uncover the third lamp of a stoplight (4-door option).

       NOTE
After performance of the above-stated operations internal facing of a roof is fixed only in front and behind. You watch that at removal facing was not soiled by lubricant. If the car is equipped with the moving hatch in a roof, it is necessary to remove a molding around its aperture.


Fig. 11.93. An arrangement of the elements dismantled for removal of facing of a roof


4) remove internal facing of a roof (fig. 11.93) for what:
— having turned on 90 °, remove the central percussion cap behind (5-door option);
— turn out six screws with percussion caps;
— lift facing of a roof over consolidations;
— take internal facing of a roof through a back doorway (5-door option);
— cast away both front seats in "sleeping" situation, lift facing of a roof over clamps on a rack In (4-door option);
— take out assembly fingers from racks With and And;
— take internal facing of a roof through a doorway of the passenger.

       NOTE
If internal facing of a roof needs replacement, from the passenger it is necessary to cut out openings for fastening of a hand-rail.


Fig. 11.94. An arrangement of elements of fastening of the panel of facing of a ceiling (figures designated various elements of fastening and their location)


You make installation of internal facing of a roof (fig. 11.94) as follows:
— combine facing with apertures for lighting plafonds, arms of sun-protection peaks and the moving hatch (at its existence);
— establish facing in clamps;
— put a molding around the moving hatch (at its existence);
— miss conducting for a rear-view mirror with illumination;
— establish sun-protection peaks;
— establish forward percussion caps if the rear-view mirror with illumination is established, pass and connect conducting;
— establish two percussion caps of a rack of D (5-door option);
— establish two percussion caps of a rack With;
— establish the central percussion cap behind;
— establish facing for a door of a back and a doorway sealant;
— you carry out further assembly to the sequences, the return dismantling.

"previous page
11.5.23. Replacement of the locking mechanism of a back of a back seat
following page"
11.5.25. Replacement of a floor covering