S40/V40
1. General information
2. Operation and maintenance of the car
3. Design and technical characteristics of engines
4. Repair of the engine
5. Transmission
6. Brake system
7. Forward suspension bracket and steering
8. Back suspension bracket
9. Control system of the Fenix 5.1 engine
10. Electric equipment. Conducting and components
11. Body
11.1. General information
11.2. Control sizes of a body
11.3. Ways of connection of details at restoration of operational qualities of a body
11.4. Repair of a body
11.5. Removal and installation of elements of a body of the car
11.5.1. Removal and installation of a cowl
11.5.2. Removal and installation of a forward wing
11.5.3. Adjustment of situation and clamp of the lock of doors
11.5.4. Removal of panels of facing of doors
11.5.5. Removal and installation of a door assembled
11.5.6. Removal and installation of the lock of a forward door
11.5.7. Removal and installation of the lock of a back door
11.5.8. Replacement of the mechanism of a window regulator of a forward door
11.5.9. Replacement of the mechanism of a window regulator of a back door
11.5.10. Installation of mechanisms of window regulators
11.5.11. Replacement of a gas-filled emphasis of a trunk lid
11.5.12. Adjustment of provision of a trunk lid
11.5.13. Replacement of elements of the lock of a trunk lid
11.5.14. Replacement of the mechanism of the lock of a trunk lid
11.5.15. Adjustment of the lock of a trunk lid
11.5.16. Replacement of a door of a back
11.5.17. Replacement of the lock of a door of a back
11.5.18. Removal and installation of the mechanism of the lock of a door of a back
11.5.19. Replacement of the block of a back lamp assembled
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
11.5.21. Removal and installation of bumpers
11.5.22. Replacement of a front seat assembled
11.5.23. Replacement of the locking mechanism of a back of a back seat
11.5.24. Replacement of internal facing of a roof
11.5.25. Replacement of a floor covering
11.5.26. Removal of the back central console
11.5.27. Removal of the forward central console
11.5.28. Removal of the dashboard assembled
11.5.29. Replacement of the dashboard
11.5.30. Installation and adjustment of a cable of control of the air mixer
11.5.31. Installation of a combination of devices
12. Schemes of electric equipment
 



13c91ae0




11-5-22-zamena-perednego-sidenya-v-sbore.html

11.5.22. Replacement of a front seat assembled

       PREVENTION
Before performance of work on front seats it is necessary to block SIPS system safety cushions. After completion of works it is necessary to unblock these pillows. It is impossible to put effort to a sitting sidewall.


Fig. 11.86. Location of the interlock of a safety cushion of the SIPS system


Blocking of a safety cushion of the SIPS system (fig. 11.86) you make (by means of the device for safe transportation) as follows:
— uncover up;
— remove the device for safe transportation from the panel;
— pull the device for safe transportation over the sensor module.
You make unblocking of a safety cushion of the SIPS system as follows:
— remove the device for safe transportation from the sensor module;
— install the device for safe transportation from the holder on panels;
— put a cover into place.

Fig. 11.87. Removal of a front seat: 1 — protective covers; 2 — a seat belt


You make removal of a seat (fig. 11.87) as follows:
— block a SIPS system safety cushion;
— remove a seat belt 2 from fastening (through an aperture for a SIPS system safety cushion);
— remove two protective covers 1 in a forward part of the directing sled (shift panels forward);
— having wrung out sideways, remove the side panel (the torx 20 screw behind);
— remove the back central console;
— turn off fixing bolts and nuts;
— disconnect sockets of heating elements (under a seat);
— disconnect the seat belt lock socket (under a seat);
— lift a seat vertically up and remove it.
You make installation of a front seat as follows:

       PREVENTION
At first be convinced that the safety cushion of the SIPS system of a new front seat is blocked by means of the device for safe transportation fixed on the sensor module.

— put a seat and tighten fixing bolts and nuts by hand;
— adjust the provision of a seat and tighten fixing bolts and nuts the moment of 40 N · m;
— establish protective covers;
— install the back central console;
— establish a seat belt, the moment of an inhaling of 45 N · to m;
— unblock a SIPS system safety cushion.

Fig. 11.88. Removal of a guide of a sled


You make removal of a guide of a sled (fig. 11.88) as follows:
— block a SIPS system safety cushion;
— remove a seat belt;
— squeeze and disconnect the unlocking bracket, remove it;
— disconnect a cross-piece, having turned off one nut from outside on which replacement will be carried out;
— turn out a forward bolt;
— when replacing an internal guide remove the seat belt lock;
— turn out a back bolt and remove a guide (with the pneumatic shock-absorber).

       NOTE
When replacing the pneumatic shock-absorber it is necessary to produce from it gas for what drill 4 mm an opening, as shown in fig. 11.88.

You make installation of a guide of a sled as follows:
— rearrange a tension spring of a guide (if necessary);
— connect the pneumatic shock-absorber and install it in a frame;
— put a back bolt;
— shift a seat forward and put a forward bolt;
— tighten a bolt the moment of 15 N · m;
— put a cross-piece and tighten a nut the moment of 20 N · m;
— put the seat belt lock, tighten the moment 48 N · m;
— put the unlocking bracket (squeeze);
— when replacing an internal guide put the seat belt lock, tighten the moment 48 N · m;
— establish a seat;
— unblock an inflatable pillow of the SIPS system.

"previous page
11.5.21. Removal and installation of bumpers
following page"
11.5.23. Replacement of the locking mechanism of a back of a back seat