S40/V40
1. General information
2. Operation and maintenance of the car
3. Design and technical characteristics of engines
4. Repair of the engine
5. Transmission
6. Brake system
7. Forward suspension bracket and steering
8. Back suspension bracket
9. Control system of the Fenix 5.1 engine
10. Electric equipment. Conducting and components
11. Body
11.1. General information
11.2. Control sizes of a body
11.3. Ways of connection of details at restoration of operational qualities of a body
11.4. Repair of a body
11.5. Removal and installation of elements of a body of the car
11.5.1. Removal and installation of a cowl
11.5.2. Removal and installation of a forward wing
11.5.3. Adjustment of situation and clamp of the lock of doors
11.5.4. Removal of panels of facing of doors
11.5.5. Removal and installation of a door assembled
11.5.6. Removal and installation of the lock of a forward door
11.5.7. Removal and installation of the lock of a back door
11.5.8. Replacement of the mechanism of a window regulator of a forward door
11.5.9. Replacement of the mechanism of a window regulator of a back door
11.5.10. Installation of mechanisms of window regulators
11.5.11. Replacement of a gas-filled emphasis of a trunk lid
11.5.12. Adjustment of provision of a trunk lid
11.5.13. Replacement of elements of the lock of a trunk lid
11.5.14. Replacement of the mechanism of the lock of a trunk lid
11.5.15. Adjustment of the lock of a trunk lid
11.5.16. Replacement of a door of a back
11.5.17. Replacement of the lock of a door of a back
11.5.18. Removal and installation of the mechanism of the lock of a door of a back
11.5.19. Replacement of the block of a back lamp assembled
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
11.5.21. Removal and installation of bumpers
11.5.22. Replacement of a front seat assembled
11.5.23. Replacement of the locking mechanism of a back of a back seat
11.5.24. Replacement of internal facing of a roof
11.5.25. Replacement of a floor covering
11.5.26. Removal of the back central console
11.5.27. Removal of the forward central console
11.5.28. Removal of the dashboard assembled
11.5.29. Replacement of the dashboard
11.5.30. Installation and adjustment of a cable of control of the air mixer
11.5.31. Installation of a combination of devices
12. Schemes of electric equipment
 



13c91ae0




11-5-21-snyatie-i-ustanovka-bamperov.html

11.5.21. Removal and installation of bumpers

Fig. 11.80. Removal of a front bumper


You make removal of a front bumper (fig. 11.80) as follows:
— remove the lower guard of the engine;
— remove clamps in the lower part of a bumper (2 pieces);
— remove an overlay of a bumper (2 screws self-tapping screws);
— remove fastening of a bumper on a side wing (2 screws self-tapping screws);
— turn out four bolts of a cross-piece from below;
— disconnect sockets of fog lights, a sound signal, dimensional lamps and screen wipers of headlights;
— lift levers of screen wipers of headlights;
— remove a bumper;
— disconnect a hose of a washer of headlights at a tee.
You make installation upside-down. Surely adjust the provision of a bumper. Moment of an inhaling of bolts of 40 N · m.

Fig. 11.81. Dismantling of a front bumper


You make dismantling of a front bumper (fig. 11.81) as follows:
— remove dimensional lamps (press latches);
— remove a spoiler (17 brackets);
— remove levers of screen wipers of headlights;
— remove knot of the electric motor and lever of a screen wiper of a headlight assembled;
— remove the plug of screen wipers of a headlight;
— remove a sound signal and fog lights;
— remove a strip slip;
— remove a basic bar and fastening;
— remove a molding (at first take out a clamp, and then remove, having shifted, a molding).
You make assembly upside-down.
You make removal of a rear bumper as follows:

Fig. 11.82. The elements dismantled before removal of a rear bumper


— remove the negative plug of the accumulator (fig. 11.82);
— remove a floor covering in a luggage carrier;
— remove an overlay of an internal part of a rear bumper in a luggage carrier;
— take out percussion caps And yes take away side panels inside;

Fig. 11.83. The elements dismantled for removal of a rear bumper: 1 — screws self-tapping screws of fastening of a bumper on a wing; 2 — percussion caps of fastening of an overlay of a bumper


— outside of the car remove an overlay of a bumper, having taken out percussion caps of 2 (fig. 11.83);
— fastening of a bumper on a wing, screws self-tapping screws 1 (2 pieces);
— disconnect sockets of dimensional lamps;

Fig. 11.84. Elements of fastening of a rear bumper: 1 — nuts of fastening of a bumper; 2 — bolts of fastening of a bumper; 3 — screws of fastening of a bumper; 4 — a percussion cap under the central part of a bumper


— turn off (fig. 11.84) screws 3, nuts 1, and bolts 2;
— take out a percussion cap 4 under the central part of a bumper;
— remove a rear bumper.
You make installation upside-down. Moment of an inhaling of bolts of a body of 40 N · m. Moment of an inhaling of bolts of a sidewall of 5 N · m.

Fig. 11.85. Dismantling of a rear bumper


You make dismantling of a rear bumper (fig. 11.85) as follows:
— remove dimensional lamps (press latches);
— remove a side assembly plate;
— put forward a spoiler (4 percussion caps and 2 clamps);
— remove a basic bar (8 clamps) and its fastening (16 clamps);
— remove a strip slip (2 percussion caps);
— having taken out 14 clamps, disconnect a molding.
Assembly of a rear bumper is made upside-down.

"previous page
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
following page"
11.5.22. Replacement of a front seat assembled