S40/V40
1. General information
2. Operation and maintenance of the car
3. Design and technical characteristics of engines
4. Repair of the engine
5. Transmission
6. Brake system
7. Forward suspension bracket and steering
8. Back suspension bracket
9. Control system of the Fenix 5.1 engine
10. Electric equipment. Conducting and components
11. Body
11.1. General information
11.2. Control sizes of a body
11.3. Ways of connection of details at restoration of operational qualities of a body
11.4. Repair of a body
11.5. Removal and installation of elements of a body of the car
11.5.1. Removal and installation of a cowl
11.5.2. Removal and installation of a forward wing
11.5.3. Adjustment of situation and clamp of the lock of doors
11.5.4. Removal of panels of facing of doors
11.5.5. Removal and installation of a door assembled
11.5.6. Removal and installation of the lock of a forward door
11.5.7. Removal and installation of the lock of a back door
11.5.8. Replacement of the mechanism of a window regulator of a forward door
11.5.9. Replacement of the mechanism of a window regulator of a back door
11.5.10. Installation of mechanisms of window regulators
11.5.11. Replacement of a gas-filled emphasis of a trunk lid
11.5.12. Adjustment of provision of a trunk lid
11.5.13. Replacement of elements of the lock of a trunk lid
11.5.14. Replacement of the mechanism of the lock of a trunk lid
11.5.15. Adjustment of the lock of a trunk lid
11.5.16. Replacement of a door of a back
11.5.17. Replacement of the lock of a door of a back
11.5.18. Removal and installation of the mechanism of the lock of a door of a back
11.5.19. Replacement of the block of a back lamp assembled
11.5.20. Replacement of a cover of a filling mouth of the fuel tank
11.5.21. Removal and installation of bumpers
11.5.22. Replacement of a front seat assembled
11.5.23. Replacement of the locking mechanism of a back of a back seat
11.5.24. Replacement of internal facing of a roof
11.5.25. Replacement of a floor covering
11.5.26. Removal of the back central console
11.5.27. Removal of the forward central console
11.5.28. Removal of the dashboard assembled
11.5.29. Replacement of the dashboard
11.5.30. Installation and adjustment of a cable of control of the air mixer
11.5.31. Installation of a combination of devices
12. Schemes of electric equipment
 



13c91ae0




11-5-2-snyatie-i-ustanovka-perednego-kryla.html

11.5.2. Removal and installation of a forward wing

Fig. 11.53. Removal of a forward wing: 1 — bolts of the top fastening of a forward wing (3 pieces);
2 — the side repeater of the index of turn;
3 — bolts of the lower fastening of a forward wing (2 pieces); 4 — bolts of fastening of the flap (2 pieces);
5 — screws of fastening of the flap (2 pieces); 6 — percussion caps of fastening of the flap (3 pieces); 7 — the connector screw a bumper/wing; 8 — bolts of forward fastening of a forward wing (2 pieces)


You make removal of a forward wing (fig. 11.53) as follows:
— remove the flap;
— remove the forward index of turn, having turned out the screw;
— remove the side repeater 2 indexes of turn on a wing;
— remove an overlay of a threshold;
— turn out the bumper connector screw 7 with a wing;
— turn off fastenings of a forward wing — forward (bolts 8), top (bolts 1), lower (bolts 3);
— remove consolidation (polyfoam);
— turn out a bolt behind a loop of a forward door;
— accurately remove a forward wing;
— remove the available percussion caps and lamellar nuts and rearrange them on a new wing.
You make installation of a new wing as follows:
— clear the internal surface of a forward wing and the surface of fastening to a body;
— process the cleared elements anticorrosive structure;
— establish a forward wing on the place;
— tighten the top bolts (the moment of an inhaling of 6 N · l);
— put a new protective molding.

"previous page
11.5.1. Removal and installation of a cowl
following page"
11.5.3. Adjustment of situation and clamp of the lock of doors